專業的解決方案助你成功
Professional Solutions For Success
info@wwhenry.com.cn
400-178-1933
● 固化后耐水，可作防潮膜使用
● 滲透力強，可用于加固基層
● 可用于非結構性裂縫修補
● 可低溫施工，可用于非吸收性基層
● 用于吸收性和非吸收性基層的雙組份環氧防潮處理
● 對于疏松混凝土基層可以滲透加固
● 可用于裂縫修補中的縫線式粘結系統
● 室內外均可使用
● 基層必須清潔，沒有影響粘結性能的物質
● 根據相應標準和技術資料對基層進行檢測，如有缺陷應及時報告
● 松軟的殘余物質或表層則必須通過洗刷或噴丸等方式徹底去除
● 用真空吸塵器對基層表面徹底除塵
● 顏色狀態： A組份：淺黃色透明 B組份：淺黃色透明
● 混合比： A組份： B組份=2:1（重量比）
● 施工溫度： 施工材料和地面溫度不得低于0℃
● 工作時間： 0-30分鐘
● 理論用量： 約200-400g/m2（用作防潮必須2道）
● 可通行時間： 12-24小時
● 終粘強度： 48小時后
※數據在23±2℃時的正常條件下適用
● 使用前，請打開大桶，然后將小桶中的固化劑徹底倒入大桶（注意小桶內是否完全倒盡）并用合適的電動攪拌器充分?jǐn)嚢?。多人施工，以防止過快固化（氣溫高于25℃尤其需要 注意）。
● 立即用尼龍滾筒或刮板將本品涂布于基層表面。在平整的基層施工時，可使用A3刮齒刮涂，然后用滾涂均勻涂布。確保將本品完全涂布至基層表面。
● 用作防潮膜時至少涂布兩道。僅用作非吸收性基層上的界面粘結時，可滾涂一道。為了增強環氧界面劑和自流平的粘結強度，需要在環氧界面劑滾涂固化前，均勻拋灑過量的(20 一40目)的石英砂，確保環氧界面劑與石英砂的有效粘結。徹底固化后，用吸塵器吸走過量的石英砂。
● 固化后的產品只能通過機械方式去除。
● 固化時間：12-24小時后可行走并可涂布第2道。第2道涂布完，至少24小時后方可使用反應型樹脂粘合劑安裝地板或施工自流平。
※數據在23±2℃時的正常條件下適用
● 置于原包裝內在涼爽、干燥的條件下。在低溫的條件下產品會變稠。
● 最佳施工條件：氣溫23±2℃，相對空氣濕度40%-75%。施工材料和地面溫度不得低于0℃。低溫可使固化時間延長，高溫可縮短產品的工作時間。
● 攪拌后的產品在容器中會很快固化，須盡快施工。用作防潮膜時，必須施工兩道。第一道用量：200-400g/m2，第二道用量：200-300g/m2。當基層殘余含水率大于8%時，本 品不可代替防潮密封膜使用。
● 施工時請穿戴好防護手套、眼鏡等，避免B組份與皮膚和眼睛接觸。接觸到皮膚時，用大量清水和肥皂清洗。接觸到眼睛時，立即用流動的清水沖洗15分鐘然后就醫檢查。不可 將本產品廢料倒入下水道中。
● A組份：10kg/桶 B組份：5kg/桶
● 本品須存放于5℃~35℃環境中，保質期為12個月。
Features：
Water resistant;
Can be used as damp proofing layer;
Strong penetration, improve adhesion to substrates;
Fills non-structural crack;
Can be used at non-absorbent substrates;
Can be applied at low temperature.
Uses:
As a two-component waterproofing epoxy resin for absorbent or non-absorbent base; Improve adhesion to various substrates; Can be used to repair non-structural crack in system; For indoor and outdoor
Substrate Preparation：
The substrate must be mature, sound, solid, clean and dry with good surface integrity. The substrate should be tested according to corresponding standard and technical information. Any defective should be reported in time. All weak surface and residues should be removed by mechanically prepared, either by scrubbing, shot-blasting or similar, and be vacuumed clean.
Technical Data:
Color： Part A： transparent light yellow
Part B： transparent light yellow
Mixing ratio： 2:1
Application temperature： material and substrate temperature above 0℃
Working time： 0-30 mins
Consumption： About 200-400g/m2（two coats are required as damp proof layer）
Walkability： 12-24 hours
Full cure： After 48hours
※Testing condition is at 23ºC ±2 ºC standard laboratory.
Mixing and Application：
1. First, the entire contents of the Part B container should be poured into the Part A container, then thoroughly mix with an electric drill fitted with a paint mixer or a wing type paddle. Work to an area that suits the size of the installing team. Please note the working temperature.
2. After mixing the material should be applied without delay onto the prepared surface using a short nylon hair roller. When apply on the flat surface, using A3 shaving scrapers and then use the roller coating uniformity .Ensure that the entire surface is coated.
3. Use as damp proof: two coats. Use as primer on the absorbent surface: one coat .
4. To improve the tensile bond strength, while HENRY521 is still wet, sanding with plenty of silica sand (20-40mesh).After curing, the extra sand should be vacuumed clean.
5. Cured product would be removed with mechanical method only.
6. Ready for light traffic and apply the second coat: about12-24 hours .Allow to dry at least 24 hours after the second coat, apply the reaction resin adhesive or self-leveling cement.
Notes：
1. The original package should be stored in cool, dry conditions. Lower temperature may decrease the fluidity.
2. Recommended condition：23±2℃,40%-75%RH. Do not apply at temperatures below 0°C.Working time will be extended at lower temperatures, and this time will be shorted at higher temperature.
3. Apply the products immediately after mixing. Use as damp proof: two coats. Consumption for the first coat is 200-400g/m2, for the second coat is 200-300g/m2 .When the concrete moisture content is greater than 8%, the product cannot be used as the sealing damp proof film.
4. During mixing and application the following precautions should be observed: ensure adequate ventilation and avoid contact of the material with the eyes, nasal passages, mouth and unprotected skin. Always wear protective gloves and glasses as necessary. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice and after contact with the skin wash immediately with plenty soap and water (do not use solvents).Disposal of such spillage or empty packaging should be in accordance with local waste disposal authority regulations.
Package and Storage：
Part A：10kg/bucket Part B：5kg/bucket
12 months when stored in dry conditions between 5℃~35℃.