專業的解決方案助你成功
Professional Solutions For Success
info@wwhenry.com.cn
400-178-1933
特點:
● 超強的終粘強度確保主材尺寸穩定性
● 可承受高荷載
● 固化后耐水，室內外均可使用
● 耐高溫、耐低溫、耐酸堿性
用途:
● 雙組份聚氨酯粘合劑適合粘接橡膠地板、PVC地板、軟木地板、亞麻地板及人造草皮等材料。適合在干燥基層，如：水泥砂漿、混凝土、木材、瓷磚、石材、金屬等基層上使用。尤其適用于高荷載基層上。
技術參數:
● 混合比： A組份： B組份=5:1（重量比）
● 施工溫度： 介于5℃和30℃之間
● 工作時間： 0-40分鐘
● 可通行時間： 12-24小時后
● 終粘強度： 48小時后
基礎說明:
● 表面必須結實、平整、干燥、清潔、沒有裂縫。基礎表面若不平整，請用亨歷自流平精找平。致密、光滑的基層需打磨處理。請遵守相關產品的說明書。
施工說明:
● 使用前，請打開大桶（12.5kg規格），然后將小桶（2.5kg規格）中的組份全部倒入大桶，必須使用適合的電動攪拌器充分攪拌本品，確保攪拌徹底、均勻，色澤一致。攪拌時應尤其注意容器壁和底部。用刮板將本品均勻涂布至基層表面（參見“用量表”）。鋪設地板并均勻滾壓。2-3小時后再次對地板滾壓。確保膠水充分轉移至地板背面。施工后可立即用醋酸乙酯等助劑清洗工具。
※對所鋪設地板不承擔責任。如有疑問，請進行檢測和試鋪設。注意遵守亨歷產品說明書要求。
刮齒類型 用量
● A2或A3 300-500g/m2
● B1或B2 400-600g/m2
包裝與儲存:
● A 組份：12.5kg B組份： 2.5kg
● 置于原包裝內可存放12個月。在涼爽、干燥的環境下存儲。低溫存儲會導致粘度升高，因此使用前應置于室內，使其達到室溫（至少5℃）。
安全防護:
● 對眼睛、呼吸系統和皮膚有刺激作用。吸入或與皮膚接觸可能引起過敏反應。本品與眼接觸，請立即用大量清水沖洗并就醫。立即脫去沾染本品的衣物。本品與皮膚接觸，請立即用大量清水和肥皂清洗。佩戴防護手套和眼、臉防護裝置。如遇事故或使用者感到不適，請立即就醫。（如有可能，請出示本標簽。）
Part A 12.5kg Part B 2.5kg
Features：
Excellent Grab;
Resistance to high and low temperature;
Water resistant，Chemical resistant;
For areas subject to high loads;
For indoor and outdoor.
Uses:
HENRY 210 Two-Component Polyurethane Adhesive is suitable for bonding rubber floor, PVC floor, cork floor, linoleum floor and artificial turf, material. Suitable for dry base, such as: cement mortar, concrete, wood, tile, stone, metal and other basic, especially for high load level. For indoor and outdoor.
Technical Data:
|
Mixing ratio： Working temperature： Working time： Walkability： Full cure： |
A：B = 5：1 (by weight) Between 5 ℃ and 30 ℃ 0-40 minutes After 12-24 hours After 48 hours |
Substrate Preparation:
The substrate must be mature, sound, solid, clean and dry with good surface integrity. Any repairs, levelling or smoothing should be carried out using HENRY relevant products. Please comply with the product specification.
Application:
First the entire contents of the Part B container should be poured into Part A container, then thorough mixing with an electric drill fitted to create one homogeneous mix and an even color is obtained. The adhesive should be applied evenly over the substrate using the appropriate serrated trowel. Ensure that there is correct transfer of the adhesive to the back of the floorcovering .After 2-3 hours press down or roll floorcoverings again. Clean tools immediately after use with acetone or spirits. Please contact technical team for testing if you have any problems. No liable for the flooring covers.
Note to comply with HENRY product instructions
Notch Size Consumption
A2 or A3 300-500g/m2
B1 or B2 400-600g/m2
Storage:
Shelf life is approx.12 months in cool dry indoor environment above 5 ℃.
Health and Safety:
During mixing and application the following precautions should be observed: ensure adequate ventilation and avoid contact of the material with the eyes, nasal passages, mouth and unprotected skin. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice and after contact with the skin wash immediately with plenty of soap and water (do not use solvents).Prolonged contact with the skin should be avoided, especially where the user has an allergic reaction to resin-based materials. Always wear gloves and eye/face protection as necessary. Observe personal hygiene, particularly washing the hands after work has been completed or at any interruption whilst work is in progress. In case of accidents seek medical advice.