專業的解決方案助你成功
Professional Solutions For Success
info@wwhenry.com.cn
400-178-1933
特點：
● HENRY531快速修補砂漿快硬、快干 — 在1.5小時后可進行后續地材鋪設;不垂流 — 適用于水平面及垂直面修補（墻、地面）；適用于室內快速修補 —如混凝土基層及混凝土樓梯踏步；適用于砂漿基面破損及裂縫的修補。
產品說明：
● HENRY531快速修補砂漿是一種用于室內修補的早凝快干、抗垂流的特種功能性砂漿。該產品干固很快并能提供您所期望的砂漿強度和硬度。在20℃環境下,工作時間約15分鐘,1.5小時即可硬化上人行走,接續進行其它施工。
應用范圍：
● 整平和修補室內樓梯踏步、普通砂漿基面、混凝土地面等；填補墻面、天花板等的孔洞；修復門窗框架的四周基面；填補管道周圍孔隙；可鏝整坡道,從坡底薄邊可鏝整到正常厚度；可制作墻地面轉角處的圓弧踢腳線、樹脂地面施工前的基面修補。
基層準備：
● HENRY531可用于干燥或潮濕基面，但基面必須是堅實的，并且無灰塵、油污和其它有礙接著物。舊有基面需先去除表面污物，再用機器進行打磨（如研磨機、噴丸機、角磨機、鋼刷等），去除表面污染物打磨掉浮塵暴露出堅實的混凝土基面以確保HENRY531與基面形成最大的粘結強度。
● 對于多孔吸水性好的表面如混凝土、普通砂漿基面、磚等可不用底涂劑,除非基面吸水率太大。
● 用于直接與土壤接觸的地面時,原設計應含防潮膜處理。
拌合比例：
● 25kg HENRY531加入5.75L水 (體積比為水: 粉劑=1：3) 。
● 在一干凈攪拌桶中加入適量的清水，并倒入粉劑，進行機械攪拌直至生成無結塊、抗垂流的漿體。避免使用過量的清水。在23°C工作環境下,工作時間為10-15分鐘，但隨著溫度的升高和降低,工作時間也隨之縮短和延長。如果施工厚度為10-30mm之間，可在HENRY531中加入約1/3體積的(粒徑0-5mm)干凈粗砂或最多等體積的3mm單粒徑骨料。
● 修補局部超過20mm厚度，如深孔和裂縫，可加入最多等體積的10mm單粒徑骨料。10mm以下的修補,請直接拌和使用。
施工方法：
● 修補用鏝刀填補孔洞、裂縫和破損區域,施工時給鏝刀施一定的壓力，使得砂漿充分“潤濕”基層表面并和表面牢固接觸。約15分鐘后,以海綿沾水濕潤表面，再以鏝刀收光。一旦修補區域硬化,即可進行后續精找平施工,如果需要，可使用HENRY550高強自流平。
● 平整表面：在工作時間內,用鏝刀填補抹實，15-20分鐘后，以海綿沾水濕潤表面再以鏝刀收光。如果用于較厚修補，添加骨料后，表面不易整平，可再以“純”HENRY531進行第二遍施工以達到所期望的平整表面。HENRY531須在5℃以上使用。
覆蓋面積：
● 25kg本品以1mm施工厚度，可覆蓋約15m2
● 包裝：25kg袋裝
● 儲存期：未開封儲存于室內陰涼干燥處約6個月
技術數據：
● 粉劑
● 混合比例： 25kg本品加5.75L水
● 干粉密度: 約1.4kg/L
● 耗 用 量： 約1.6kg 粉體/mm/m2
● 濕漿
● 工作溫度： 5°C - 35°C
● 濕漿密度： 約2.0kg/L
● 初凝： 約10-15分鐘 (23°C)
● 終凝： 約60 分鐘 (23°C)
抗壓強度：
● 1 天 (23°C) ≥ 15 MPa
● 1 天 (5°C) ≥ 14 MPa
● 28 天 (23°C) ≥ 25 MPa
抗折強度：
● 1天 (23°C) ≥ 4 MPa
● 1天 (5°C) ≥ 4 MPa
● 28天 (23°C) ≥ 6 MPa
● 粘結強度： 約1.6 MPa
● 收縮： ≤ 0.15%
注意事項：
● 本品在正常使用過程中是安全可靠的。但是本品含有水泥,如直接長期接觸，可能會刺激皮膚。避免在攪拌使用中吸入粉塵。避免直接接觸眼睛和皮膚，施工時，請配戴相應的防護面具、手套和護目鏡。不慎濺入眼睛，請用大量清水沖洗幾分鐘并盡快就醫。如果吸入大量的粉塵，請保持通風狀態，并且用清水漱口。如有任何不良反應，請及時就醫。
Characteristics：
Rapid hardening, quick drying, after 1.5 hours subsequent ground material can be laid;
Don't hang down stream - suitable for horizontal and vertical plane repair (wall/floor);
Suitable for indoor rapid repair - such as concrete substrate and concrete stair step ;
Suitable for mortar base damage and crack repair.
Product Description:
HENRY 531 rapid repair mortar is a kind of using for indoor repair early coagulation quick drying, special functional vertical flow resistance mortar. The product dry solid quickly and can provide you the desired mortar strength and hardness. At 20℃ environment, work time is about 15 minutes, 1.5 hours hardening walking here, succeeded to other construction.
Scope of application:
Levelling and repair indoor stair step, the common base of mortar, concrete ground, etc;
Fill the metope, ceiling, such as holes; Repair the all around surface of door and window frame;
Rapid hardening, quick drying, after 1.5 hours subsequent ground material can be laid;
Don't hang down stream - suitable for horizontal and vertical plane repair (wall/floor);
Suitable for indoor rapid repair - such as concrete substrate and concrete stair step ;
Suitable for mortar base damage and crack repair.
Substrate Prepare:
HENRY531 can be used for the dry or wet base level, but the base must be solid, and free of dirt, oil and other hazardous to then. Old base need to remove surface dirt, and then use machine for grinding (such as grinding machine, shot blastinzg machine, grinder, steel brush, etc), to remove surface contaminants polished away dust exposed solid concrete base to ensure HENRY 531 with base to form the largest bond strength.
Good water imbibition for porous surface such as concrete, ordinary mortar base, brick can be coated, plane unless is bibulous rate is too big.
When used in direct contact with the soil ground, the original designs should be moistureproof film processing.
Mixing Proportion:
25kg henry 531 add 5.75 L water (volume ratio of water: powder = 1:3).
Mixing:
Add the right amount of water in a clean mixing barrel, and pour into powder, mechanical stirring until generation without aggregation, resistance to flow of the slurry.
Avoid using too much water. At 23℃ work environment, work time for 10-15 minutes, but with the rise and fall of temperature, working time is shortened and extended.
If the thickness of the construction is between 10-30 mm, can join about one-third the size (diameter 0-5 mm) clean coarse sand or single particle size of aggregate volume of 3 mm at most in HENRY531.
Repair local more than 20 mm thickness, such as deep hole and crack, can join up 10 mm single particle size of aggregate volume, etc.10 mm below the repair, please directly mixing to use.
Construction:
Repair with a trowel fill holes, cracks and damage area, construction to trowel with certain pressure makes the mortar "wetting" surface at the grass-roots level and fully and solid surface contact. After about 15 minutes, with sponge water wet surface, light by trowel mark again. Once the repair area hardening, can for subsequent eveling construction, if necessary, can use HENRY High strength self-leveling.
Flat surface: in working hours, with a trowel fill compaction, after 15- 20 minutes, the water in sponge moist surface by trowel mark light again. If for thicker, after adding aggregate, surface not easily leveling, can be with "pure" HENRY 531 to do the second time again in order to achieve the desired flat surface.
HENRY 531 must be used in more than 5℃.
Cover Area:
25 kg of this product with 1 mm construction thickness, covering about 15m2
Packing:
25 kg bags
Storage Life:
Store unopened in dry indoor shade place about six months
Technical data:
powder
Mix proportion: 25 kg of this product plus 5.75 L water
Powder density: 1.4 kg/L
Consumption : powder is about 1.6 kg/mm/m2
The wet slurry:
Working temperature: 5℃-35℃
Wet slurry density: 2.0 kg/L
Initial setting: about 10-15 minutes (23℃)
Final set: about 60 minutes (23℃)
After curing
Compressive Strength:
1 days after (23℃) ≥ 15 MPa
1 days after (5℃) ≥ 14 MPa
28 days after (23℃) ≥ 25 MPa
Flexural Strength:
1 days after (23℃) ≥ 4 MPa
1 days after (5℃) ≥ 4 MPa
28 days after (23℃) ≥ 6 MPa
Bond strength: about 1.6 MPa
Shrinkage: ≤0.15%
Note:
This product is safe and reliable in the process of normal use. But this product contains cement, such as direct contact for a long time, may stimulate the skin. Avoid breathing dust in mixing to use. Avoid direct contact with eyes and skin, when construction, please wear appropriate protective mask, gloves and goggles. Accidentally splashed into eyes, please rinse with water for a few minutes and see the doctor as soon as possible. If inhaled a lot of dust, please keep the ventilation state, and gargle with water.
If you have any adverse reaction, please timely medical treatment.