專業的解決方案助你成功
Professional Solutions For Success
info@wwhenry.com.cn
400-178-1933
產品描述：
HENRY 135 ?；u石材粘合劑是優選天然礦物原料和改性聚合物配制而成的粘合劑。該產品相對于傳統的水泥砂漿更具有粘結力、施工便捷、薄貼工藝節省空間、減少材料損耗，其超強的粘結力使低吸水率的瓷磚鋪貼更持久牢固。
產品特點：
● 優異的抗滑移性能;
● 施工性好、耐候性好;
● 粘結力好、防止磚脫落。
用法用量：
1、將產品倒入清水中攪拌成膏狀，注意要先加水后再倒入產品，攪拌時使用電動攪拌機；
2、混合比：25kg產品：5.0-5.5L清水
3、充分攪拌均勻至無粉團，攪拌完成后需靜置五分鐘，再稍作攪拌后使用，更有利于增加粘結力。
4、用齒形刮刀膠膏狀瓷磚膠均勻涂布于基層表面，并形成均勻條齒狀。單次涂布面積建議不超過1m²（可視天氣溫度適當調整），然后在晾置時間內鋪貼瓷磚即可。
5、齒形刮刀的選擇應根據工作面的平整度和瓷磚背面的凹凸程度而定。
6、如瓷磚背面凹凸程度較大，則應進行雙面涂膠，即在工作面和瓷磚背面同時涂上瓷磚膠。
7、用量：1.5kg/m²/mm。
注意事項：
1、該產品按參考比例加水即可使用，禁止添加其它材料。
2、施工溫度為5-35℃；
3、水粉比例可因基層、天氣、施工條件等不同而做出適當調整；
4、攪拌好的粘合劑應在2小時內使用完畢，杜絕將已干結的粘合劑拌水使用；
5、鋪貼施工完成后，需待粘合劑完全干固后，24小時后才可以進行下一步的填縫工作；
6、鋪貼瓷磚時，磚與磚之間必須留有≥2㎜的縫隙；
7、在進行墻面鋪貼時，注意做好臨時固定措施。
8、室內施工高度應≤4m。
執行標準：JC/T 547-2017 C1T
儲存運輸： 本品須存放于干燥、通風的室內環境，防潮、防水、防止暴曬，保質期為12個月。
包裝： 20KG、25KG/包
HENRY 135 Porcelain and Stone Adhesive
Discription:
The Porcelain and Stone Adhesive is made of natural mineral materials and modified polymer. Comparing with traditional cement mortar, this product has advantages of good adhesion, easy to use, environmental-friendly and safety. The thin paste method can save space and materials; the super adhesion make sure the tiles with low water absorption can be applied with more durability and firmness.
Features:
Excellent slip resistance; Good adhesion;
Prevent the tiles from falling off;
Easy to use and good weather resistance.
Application:
1. The powder should be added into clean water in a clean container whilst stirring vigorously and mixed thoroughly to give easily worked mortar.
2. Mixing ratio: powder: water =25Kg: 5-5.5L;
3. Allow to stand for 3 minutes during the mixing, then restir the mortar thoroughly. This procedure can increase the bonding strength of the mortar.
4. Apply the mortar evenly on the surface of the substrate with a notched trowel and make sure to press the tiles into the freshly combed mortar in open time.
5. The type of notched trowel is depending on the substrate conditions and size of tiles.
6.To increase the bonding strength, both of the substrate and back of the tiles should be applied with mortar.
7. Coverage: 1.5kg/mm/m2.
Notes:
1. Please following the mixing ratio, other materials should not be added during the mixing.
2. The application temperature is 5-35 ℃;
3. The water/powder ratio will vary depending on the substrate, weather and site condition;
4. The mortar should be applied within approx.2 hours. Do not reuse the dry mortar by adding water again;
5. Grouting may be allowed approximately 24 hours after the application;
6. Seamless application is forbidden, the width of tile joints should be ≧ 2mm
7. Pay attention to provisional fixing measures during the wall application
8. Interior application height should be ≤ 4 m.
Technical Data：
JC/T 547-2017 C1T
Storage& Shelf Life:
This product has a shelf life of approximately 12 months if stored in a dry, cool, ventilated place in original unopened packaging
Package:20kg、25kg/bag
Notes:
If in doubt, create small area trial before large area application. we are not responsible for the loss caused by ignoring the problems occurred in trial. if you have any questions about application, please consult our technical support team.