欧美四虏免费一级成人片,岳饥渴难耐好爽好大,在线高清不卡无码视频,日日碰狠狠添天天爽

 

產品描述：

HENRY 523 高彈防水涂料是以優質改性聚合物乳液和水泥為主要原料，添加多種助劑、填充料精致而成的雙組份水性防水涂料。防水涂膜拉伸強度高，與基層粘結良好，對于防水膜施工后需粘貼瓷磚，砂漿鏝涂的場所特別適用。應用于屋頂、陽臺、衛浴、廚房、茶水間、地下室、游泳池、蓄水池、內外墻面等。

 

產品特點：

● 水性環保；

● 防水、透氣、耐候性佳；

● 延展性佳，抗基層形變能力強。

 

用法與用量：

1、清理基面，充分潤濕基層后施工更佳；

2、將B組份倒入干凈的攪拌容器中，然后按照粉液比2:1的比例一邊攪拌一邊緩慢加入A組份，充分?jǐn)嚢柚辽珴梢恢隆?/p>

3、用刷子將漿料均勻地涂刷在處理好的基材上，根據使用環境涂刷2層或2層以上。

4、每做完1層，必須待其表干（約1～3小時）后，再做第2層，涂刷方向與第1層垂直。每1層涂刷厚度不超過1mm，以利于固化。

5、涂層施工完后，應自然養護7天。應對防水涂層進行隔離保護，以免破壞。

用量：1.2-1.5kg/m²

 

注意事項：施工環境溫度應在5-35℃。陰雨天或基層有明水時不能施工。每次施工需涂布2層以上，應避免漏涂。施工后設備與工具應立即用水清洗。

 

執行標準：GB/T 23445-2009 Ⅱ型

 

儲存運輸：本品須存放于干燥、通風的室內環境，防潮、防水、防止暴曬，保質期為12個月。

 

包裝： 25KG/包，7KG/桶，18KG/桶

 

 

 

HENRY523 High-Flex Waterproof Membrane

 

 

Discription:

HENRY523 is a 2-component waterproof membrane with high quality modified polymer, emulsion, cement, various additives and fillers. The product has high tensile strength and suitable for most substrates, especially suitable for areas to be covered by tiles or mortar. Can be applied on roof, balcony, bathroom, kitchen, tea room, basement, swimming pool, cistern, interior and exterior wall, etc.

 

Features:

Environmental protection, low odor;

Flexible-accommodates normal building movement.

Waterproof, breathable, weather resistance, ultraviolet-proof

 

Application:

1.Prepare the substrate, fully wet surface is more suitable for application.

2. Pour component B liquid into a clean mixer, then slowly add component A powder by mixing ratio of powder: liquid=2:1 while mixing. The mixing time should be 3-5 minutes.

3. Apply the slurry evenly to the substrate with a brush or roller, apply 2 or more layers depending on the condition.

4. The following coat should be applied when the previous coat is slightly dry and solid (but not fully dried). The direction of the following coats should be vertical to the previous one. For easy curing, the thickness of each coat should not over 1mm.

5.After coating application, it should be maintained for 7 days. The site should be isolation protected.

Coverage: 1.0-1.5kg/m2/ layer

Notes:

The application temperature condition should be 5-35℃. application cannot be carried out on rainy days or when there is open water on the substrate. The product should be evenly applied by 2 or more coats. tools should be cleaned by water immediately after application.

 

Standards:GB23445-2009 II

 

Storage& Shelf Life:

This product has a shelf life of approximately 12 months if stored in indoor temperature for 5-35°C in original unopened packaging, avoiding sun exposure or freeze.

 

Package:18 kg/barrel