欧美四虏免费一级成人片,岳饥渴难耐好爽好大,在线高清不卡无码视频,日日碰狠狠添天天爽

產品描述：

HENRY 522 柔性防水漿料粉料是由高強硅酸鹽水泥、優質骨料、添加劑和聚合物乳液等原料精制而成。用于混凝土、水泥砂漿、地下室、露臺及陽臺、游泳池、儲水池、浴室地面及廚房等防水抗?jié)B工程，對于防水膜施工后需粘貼瓷磚，砂漿鏝涂的場所特別適用。

產品特點：

● 能夠覆蓋毛細裂縫；

● 綠色環保，施工便捷；

● 易混合，可刷涂、滾涂；

● 附著力強，粘結強度高。

用法與用量：

基層處理：混凝土、砂漿基礎面和磚體表面必須清潔、無油污及松散附著物，所有表面應盡量平整。施工前，若基礎表面有吸水性，則應使其吸水至飽和，但不能有積水。

1、將B組份倒入干凈的攪拌容器中，然后按照粉液比3:1的比例一邊攪拌一邊緩慢加入A組份，徹底攪拌至色澤一致。

2、用刷子或滾筒將漿料均勻地涂刷在處理好的基材上，根據使用環境涂刷2層或2層以上。

3、每做完1層，必須待其表干（約2～4小時）后，再做第2層，具體情況視基面的密實度以及當時的氣溫而定。如果在涂層已經固化時再做第2層，必須先用清水重新潤濕表面。

4、養護：涂刷完后第二天起，建議用噴霧或濕布覆蓋涂層2-3天再進行閉水試驗；對于長期浸水環境，應待其空置兩周后才盛水。用量：1.5-2.0kg/m²
 

執行標準：JC/T 2090-2011 Ⅰ型

儲存運輸：本品須存放于干燥、通風的室內環境，防潮、防水、防止暴曬，保質期為12個月。

包裝： 25KG/包，7KG/桶，18KG/桶

HENRY 522 Flexible  Waterproofing Slurry

Description:

The product is a 2-component waterproof slurry made of high strength Portland cement, high quality aggregate, additives, polymer emulsion, fully meet the requirements of standard JC/T2090-2011(Type I), can be applied on concrete, cement mortar substrates in basement, terrace and balcony, swimming pool, storage pool, bathroom, kitchen and other waterproof areas, especially suitable for areas to be covered by tiles or mortar.

Features:

Environmental protection;

Easy to use;

Can be applied on slight cracks;

Excellent bonding strength.

Application:

Substrate Preparation: the surface to be coated should be dry, clean, sound and free from oil, grease, laitance and flaking paint. Make sure the surface is water saturated and with no water visible on the substrate with water absorbency.

1.Pour component B liquid into a clean mixer, then slowly add component A powder by mixing ratio of powder: liquid=3:1 while mixing. The mixing time should be 3-5 minutes.

2.Apply the slurry evenly to the substrate with a brush or roller, apply 2 or more layers depending on the condition.

3.The following coat should be applied when the previous coat is slightly dry and solid (but not fully dried), which generally takes 2-4 hours. Drying time will vary depending substrate and temperature condition. If the previous coat is fully dried, wet the surface before next application.

4.Maintenance: from the second day after application, it is recommended to cover the coating with wet cloth or water spray for 2-3 days before the closed water test. For long-term immersion area, the site should be maintained at least 2 weeks before being filled with water.

Coverage: 1.5-2.0kg/m²/ layer

Notes:

The application temperature condition should be 5-35℃.The open time of the product is approx.30 minutes. The application should not be carried out under the environment of direct sunlight or strong winds. Please follow the mixing ratio and do not add water into the mixture. The product can be only applied on a well-prepared, firm substrate. Tools should be cleaned by water immediately after application, dried product residues can be removed proper machine.

Standards: JC/T2090-2011 I

Storage& Shelf Life:

This product has a shelf life of approximately 12 months if stored in indoor temperature for 5-35°C in original unopened packaging, avoiding sun exposure or freeze.

Package:18 kg/barrel